Everybody knows someone who has had flooding in their laundry room. The most common problems are when the washing machine overflows or the water inlet hose bursts. This happens somewhere everyday. Most above ground floor laundry rooms have no provision for water emergencies so when trouble strikes it floods the entire house, ruining floors, drywall and creates mold. All this can be avoided by installing the “Trap Guard Waterproof Hub Drain” which funnels away uncontrolled water. The “Trap Guard Waterproof Hub Drain” is attractive, barely noticeable and is easily installed in the laundry room using a small 4” hole that can be connected to the plumbing stack or simply drained through an outside wall. The “Trap Guard” part protects against sewer gas and bugs from entering your house. It is simple to install and can save many thousands of dollars in water damages.

Water damage is a major inconvenience and cost for building tenants and owners. It is also a primary cause of major claims for insurance carriers. If you add to this situation the expanding problem of health and liability concerns for mold buildup due to water between floors and in walls, the containment of water damage becomes critical.

Because all but the least expensive ProVent pipe penetrations automatically waterproof, this prevents the water resulting from an emergency from using penetrations as a path to multi-floor and between-floor damage. ProVent drain technology complements this by providing a safe way to remove the water.

And, because the Trap Guard® does not require a trap or a vent, it can be used for emergency water drainage in any location in a building. This can be tied into a dedicated Emergency Drain System for the building, with the runoff emerging at ground level.

There are many potential causes of water emergencies. In a multi-story office building, they could be the result of the use of the sprinkler system, either for a fire or by accident. Or, perhaps they could be the result of an after-hours burst pipe or an overflowing toilet. Regardless of cause, the ability to drain away excess water, combined with waterproof penetrations, will significantly cut down on damage and inconvenience. it will also reduce the possibility of mold buildup.

For multi-story residential buildings, the potential for water emergencies is increased by the potential for burst washing machine hoses and bathroom overflows. Since ProVent has a drain that can be used and sealed with a wooden floor, both wood frame and concrete multi-story residential buildings can be equipped with a Trap Guard-based Emergency Drain System. Until now this was not possible for buildings with wood floors.

In both office and residential buildings, this combination of sealed penetrations and ability to drain away excess water makes true tenant separation possible.

Trap Guard® US Patent Number: 6,795,987

Underground Hub Drains:

Part #	Description	PDF
TG23HD	2″ X 3″ TG Underground Hub Drain – Connecting to Plastic	view
TG24HD	2″ X 4″ TG Underground Hub Drain – Connecting to Plastic	view
TG34HD	3″ X 4″ TG Underground Hub Drain – Connecting to Plastic	view
TG23HD-RS	For recessed strainer 1-1/4″, add RS after part number	view
The part numbers for the four drains (immediately above) are for 3″. For 2″ or 4″ change the first number to 2 or 4.

Floor Drains:

Part #	Description	PDF
TG23FHD	2″ X 3″ TG Above Ground Hub Drain	view
TG23FHDS	2″ X 3″ TG Above Ground Hub Drain with Strainer	view
TG23FHDRS	For recessed strainer 1-1/4″, add RS instead of S in the part number	view
TG24FHD	2″ X 4″ TG Above Ground Hub Drain	view
TG24FHDS	2″ X 4″ TG Above Ground Hub Drain with Strainer	view
TG23FBHD	2″ X 3″ TG Above Ground Bottom Mount Hub Drain	view
TG23FBHDS	2″ X 3″ TG Above Ground Bottom Mount Hub Drain with Strainer	view
TG24FBHD	2 x 4 TG Above Ground Below Deck Hub Drain	view
TG24FBHDRS	2 x 4 TG Above Ground Below Deck Hub Drain with Recessed Strainer	view

Part #	Description	PDF
TG22-SC	2″ TG Fits into 842-2 Sioux Chief tailpiece	view
TG33-SC	3″ TG Fits into 842-3 Sioux Chief tailpiece	view
TG34-SC	4″ TG Fits inside 842-4 Sioux Chief tailpiece	view
TG3H	3″ TG Fits inside Smith 2000 and Josam 3000 tailpiece	view
TG34HM	3″ TG Fits inside Mifab tailpiece	view
TG34HW	3″ TG Fits inside Watts tailpiece	view
TG33-Wade	3″ TG Fits inside Wade tailpiece	view
TG33-Zurn	3″ TG Fits inside Zurn Z415 tailpiece	view

Part #	Description	PDF
T2563H-F-SSW	2″ Adj. NB FD for plastic pipe above ground floor	view
T3563H-F-SSW	3″ Adj. NB FD for plastic pipe above ground floor	view
T4563H-F-SSW	4″ Adj. NB FD for plastic pipe above ground floor	view
T3563H-F-SSW-CP	Add CP to part number for 5″ chrome strainer & tailpiece.	view
T3563H-F-SSW-PB	Add PB to part number for 5″ brass strainer & tailpiece.	view
T3563H-F-SSW-SQ	Add SQ to part number for 5″ square strainer.	view
T3563H-F-SSW-FU	Add FU for a 2-3/8″ x 3-1/2 funnel trap top.	view
H=pour depth of floor-Change the H in part number to pour height – for example: for a 6″ pour, H=6 All above Trap Guard® Drains have 5″ Nickel Bronze round tops. The part numbers for the four drains (immediately above) are for 3″. For 2″ or 4″ change the first number to 2 or 4.

Part #	Description	PDF
T23FHD-SSW	2″ Trap Guard® Combo Hub/Floor Drain with built-in, intumescent wrap strips	view
T23FHDS-SSW	2″ Trap Guard® Floor Drain with built-in, intumescent wrap strips and strainer flush with floor	view
T23FHDRS-SSW	2″ Trap Guard® Combo Hub/Floor Drain with built-in, intumescent wrap strips and recessed strainer	view

Part #	Description	PDF
T2563H-F-SSW-CM	2″ Adj. NB FD for plastic in corrugated metal floor	view
T3563H-F-SSW-CM	3″ Adj. NB FD for plastic in corrugated metal floor	view
T4563H-F-SSW-CM	4″ Adj. NB FD for plastic in corrugated metal floor	view
T3563H-F-SSW-CM-CP	Add CP to part number for 5″ chrome strainer & tailpiece.	view
T3563H-F-SSW-CM-PB	Add PB to part number for 5″ brass strainer & tailpiece.	view
T3563H-F-SSW-CM-SQ	Add SQ to part number for 5″ square strainer.	view
T3563H-F-SSW-CM-FU	Add FU for a 2-3/8″ x 3-1/2 funnel trap top.	view
H=pour depth of floor-Change the H in part number to pour height – for example: for a 6″ pour, H=6 All above Trap Guard® Drains have 5″ Nickel Bronze round tops. The part numbers for the four drains (immediately above) are for 3″. For 2″ or 4″ change the first number to 2 or 4.

Part #	Description	PDF
T2565H-F-SSW-CH	2″ NB FD for plastic pipe though cored hole	view
T3565H-F-SSW-CH	3″ NB FD for plastic pipe through cored hole	view
T4565H-F-SSW-CH	4″ NB FD for plastic pipe though cored hole	view
T3565H-F-SSW-CH-CP	Add CP to part number for 5″ chrome strainer & tailpiece.	view
T3565H-F-SSW-CH-PB	Add PB to part number for 5″ brass strainer & tailpiece.	view
T3565H-F-SSW-CH-SQ	Add SQ to part number for 5″ square strainer.	view
T3565H-F-SSW-CH-FU	Add FU for a 2-3/8″ x 3-1/2 funnel trap top.	view
H=pour depth of floor-Change the H in part number to pour height – for example: for a 6″ pour, H=6 All above Trap Guard® Drains have 5″ Nickel Bronze round tops. The part numbers for the four drains (immediately above) are for 3″. For 2″ or 4″ change the first number to 2 or 4.

Part #	Description	PDF
TG15PT	1 1/2″ TG fits inside a 1 1/2″ metallic or non-metallic pipe	view
TG22P	2″ TG Fits inside a 2″ PVC Pipe	view
TG22IP	2″ TG Fits inside a 2″ C.I. Pipe	view
TG22G	2″ TG Fits through a 2″ gasket to inside pipe	view
TG33IP	3″ TG Fits inside a 3″ C.I. pipe	view
TG33P	3″ TG Fits inside a 3″ PVC or ABS pipe	view
TG33G	3″ TG Fits through a 3″ gasket to inside pipe	view
TG34G	3″ TG Fits through a 4″ gasket to inside pipe	view
TG34IP	3″ TG Fits inside 4″ C.I. or plastic pipe	view
TG34TP	3″ TG Fits most 4″ strainer tailpieces	view
TG36-IP	6″ TG fits inside 6″ cast iron or plastic pipe	view

Part #	Description	PDF
T25630-F-P	2″ Adj. NB FD w/PVC plastic hub joint.	view
T35630-F-P	3″ Adj. NB FD w/PVC plastic hub joint.	view
T45630-F-P	4″ Adj. NB FD w/PVC plastic hub joint.	view
T35630-F-P-CP	Add CP to part number for 5″ chrome strainer & tailpiece.	view
T35630-F-P-PB	Add PB to part number for 5″ brass strainer & tailpiece.	view
T35630-F-P-SQ	Add SQ to part number for 5″ nickel bronze square strainer	view
T35630-F-P-FU	Add FU for a 2-3/8″ x 3-1/2 funnel trap top.	view
The first 3 Trap Guard® Drains have 5″ Nickel Bronze round tops. The part numbers for the four drains (immediately above) are for 3″. For 2″ or 4″ change the first number to 2 or 4.

Part #	Description	PDF
T25630-F-CI	2″ Adj. NB FD w/mechanical hub joint for C.I.	view
T35630-F-CI	3″ Adj. NB FD w/mechanical hub joint for C.I.	view
T45630-F-CI	4″ Adj. NB FD w/mechanical hub joint for C.I.	view
T35630-F-CI-CP	Add CP to part number for 5″ chrome strainer & tailpiece.	view
T35630-F-CI-PB	Add PB to part number for 5″ brass strainer & tailpiece.	view
T35630-F-CI-SQ	Add SQ to part number for 5″ square strainer.	view
T35630-F-CI-FU	Add FU for a 2-3/8″ x 3-1/2 funnel trap top.	view
The first 3 listed Trap Guard® Drains have 5″ Nickel Bronze round tops. The part numbers for the four drains (immediately above) are for 3″. For 2″ or 4″ change the first number to 2 or 4.

Part #	Description	PDF
T3565X-F-P	3″ Outlet Connecting to Plastic	view
T4565X-F-P	4″ Outlet Connecting to Plastic	view
T3565X-F-CI	3″ Outlet Connecting to Cast Iron	view
T4565X-F-CI	4″ Outlet Connecting to Cast Iron	view